Olympia Chimney Flue Liner Replacement Nationwide

Olympia Chimney Flue Liner Replacement: The Dallas Owner’s Guide

We stock and install Olympia Chimney-compatible stainless steel flue liners throughout Dallas, with most replacements running between $1,800 and $4,200 installed depending on liner diameter, length, and how much of the existing system needs rebuilding. Most Olympia Chimney liner replacement jobs in Dallas take one full day, and we carry the common 6-inch and 8-inch diameters on the truck so we’re not making you wait on a parts order. Homeowners usually discover the liner has failed during a routine sweep or inspection, often after noticing rust flakes at the bottom of the firebox, a musty smell after rain, or visible cracking in the clay tile above the roofline.

Call (361) 264-4483

Which Olympia Chimney Models This Applies To

Olympia Chimney has manufactured stainless steel chimney liners and venting components for decades, and their liners show up most often in Dallas in two configurations: the 316L alloy for wood-burning fireplaces and the 304 alloy for gas appliances. The most common sizes we replace in Dallas are 6-inch and 8-inch diameters, though we also handle 5.5-inch and 7-inch where an older Olympia liner was custom-cut. To identify what you have, look for the manufacturer’s label on the liner cap or the exposed section above the chimney chase – Olympia Chimney stamps their alloy type and diameter directly into the metal on most post-1995 liners. If the label is gone, we measure the inside diameter and inspect the alloy stamp during the inspection; that takes about ten minutes and tells us whether we’re matching OEM Olympia Chimney material or an aftermarket equivalent. For the record, Alcott Chimney Dallas is an independent service provider, not affiliated with Olympia Chimney – if an OEM liner is required by code or warranty, we order it; if not, we’ll quote a comparable 316L or 304 liner and show you the spec sheet before you commit.

Signs Your Olympia Chimney Flue Liner Replacement Is Failing

• Rust or corrosion staining on the firebox floor. This means moisture is getting through the liner wall, usually from a pinhole in the 304 alloy where years of condensate ate through. Once water gets behind the liner, the surrounding masonry starts absorbing it, and the problem accelerates through Dallas freeze-thaw cycles.
• Flakes of metal or discolored creosote falling during a sweep. When the liner delaminates or corrodes, creosote doesn’t adhere the same way. We’ll see shiny metal flecks in the brushings or a patchy, blistered creosote pattern that tells us the liner surface has begun breaking down.
• A persistent musty or wet-smoke odor even weeks after your last fire. That smell means smoke and moisture are bypassing the liner and leaking into the chimney chase. In Dallas, where summer humidity runs high, this gets worse in July and August even if you haven’t burned since spring.
• Visible cracks or gaps in the clay tile when viewed from the roof. Many Dallas homes with chimneys built in the 1970s and 1980s have Olympia liners installed inside deteriorating clay tile. When the tile shifts, the liner shifts with it, and the seam separation becomes a path for smoke and heat to escape.
• Water pooling around the base of the chimney after heavy rain. A failed liner cap or top plate lets rain run straight down the inside of the liner. We see this a lot in east Dallas neighborhoods like Lake Highlands after spring storms, when homeowners notice damp drywall near the fireplace chase.

Replacement Cost & What’s Included

A full Olympia Chimney flue liner replacement in Dallas typically runs $1,800 to $4,200 installed. Here’s what drives that range:

• Liner length: Most Dallas single-story chimneys need 15 to 25 feet. Two-story homes with full masonry chimneys can need 30 to 40 feet. Each foot adds liner cost and, more importantly, labor for feeding and securing it.
• Diameter: 6-inch is the workhorse size for single-flue wood fireplaces. 8-inch is common on larger fireboxes and some gas conversions. 5.5-inch and 7-inch jobs require special-order liner, which costs more.
• Condition of the existing crown and chase: If the chimney crown is cracked, which we see on nearly half the Dallas homes we inspect after a decade of Texas sun and storm cycles, it has to be repaired or replaced before the new liner goes in. Material and labor for the crown is typically $350 to $800 on top of the liner.
• Access: Steep roofs, two-story climbs, and tight chases add time. We’ll tell you plainly if your chimney is one of the ones that’s going to take longer.

Every quote we write in Dallas includes the liner, insulation if the chimney requires it, connectors, cap, and all labor. There’s no add-on surprise at the end. If we tell you $2,900 before we start, the invoice says $2,900 when we finish. The liner itself comes with a limited warranty from the manufacturer, and our installation carries a written guarantee backed by the 365-Day Done Right Promise – if the liner installation fails within a year, we return and make it right at no charge.

DIY or Call Us?

You can safely inspect your Olympia Chimney liner from the fireplace side: shine a flashlight up the flue, look for rust streaks, flaking metal, or gaps between liner sections, and check for water stains inside the firebox after rain. What you should not do is pull the liner, re-secure it, or drill into the chimney chase. A flue liner that’s been compromised is a carbon monoxide and house fire risk, and the work involves climbing ladders, handling stainless steel that can be sharp at the cut edges, and working at height – none of which belongs on a weekend project list. If your inspection shows anything suspicious, call (361) 264-4483. We’ll do a full camera inspection, show you the footage, and give you a written price before any work starts. Tell you what’s there, tell you what it costs, do the work – that’s the whole job.

FAQs